|
|
|
|||||||||||||||||||||||||||
 |
 |
||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||
-
-
- Thanksgiving Special: Free UPS Ground Shipping On Orders Over $50 (U.S. Only)
| ||||||||||||||||||||||||||||||||||||||
Knight Riderz LED Light BarsKnight Riderz Sequential LED Light Bar with Flashing Brake AlertOriginal 12 LED Knight Riderz
This light bar contains 12 high power dual intensity LEDs. In running light mode the LEDs sequence from side to side in a "Knight Rider" sequence. When the brake is applied the LED will flash for approximately 5-6 seconds then go to a solid on state until the brake is released. Both modes, running and brake, have been designed to create the maximum visibility. The unit comes pre-taped with 3M double sided tape for easy mounting to any flat surface. Simply connect the black wire to any ground wire, the Red wire to your existing brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required. Dimensions: 4.7" long x .7" wide x .7" high. Available in Red, Blue and Smoked. Blue is strictly for off-road or show use only. New Longer 21 LED Knight Riderz
This light bar contains 21 high power dual intensity LEDs. In running light mode the LEDs sequence from side to side in a "Knight Rider" sequence. When the brake is applied the LED will flash for approximately 5-6 seconds then go to a solid on state until the brake is released. Both modes, running and brake, have been designed to create the maximum visibility. The unit comes pre-taped with 3M double sided tape for easy mounting to any flat surface. Simply connect the black wire to any ground wire, the Red wire to your existing brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required. Dimensions: 7.5" long x .7" wide x .7" high. Available in Red or Smoked.
Note: Knight Riderz Light Bars can be wired independently, for example if you only want to connect the running light wire you can do so and cap off the brake light wire, if you only want to use the brake function simply cap off the running light wire. If you want to use the sequential function as a brake light instead of a running light then connect it to your brake light wire and cap off the Knight Riderz brake light wire.
Knight Rider Non-Sequential LED Light Bar with Flashing Brake Alert This light bar contains 12 high power dual intensity LEDs. In running light mode the LEDs are on in low intensity mode. When the brake is applied the LED will flash for approximately 5-6 seconds then go to a solid on state until the brake is released. Both modes, running and brake, have been designed to create the maximum visibility. The unit comes pre-taped with 3M double sided tape for easy mounting to any flat surface. Simply connect the black wire to any ground wire, the Red wire to your existing brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required. Dimensions: 4.7" long x .7" wide x .7" high. Available in Red and Smoked.
Knight Rider Non-Sequential LED Light Bar with NON Flashing Brake Alert Not into the sequential or flashing LEDs, this light bar is for you. This light bar contains 12 high power dual intensity LEDs. In running light mode the LEDs are on in low intensity mode. When the brake is applied the LED will then go to full intensity mode. The unit comes pre-taped with 3M double sided tape for easy mounting to any flat surface. Simply connect the black wire to any ground wire, the Red wire to your existing brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required. Dimensions: 4.7" long x .7" wide x .7" high. Available in Red and Smoked. These lights bars can be used as running, brake, and turn when used in conjunction with one of our controllers.
Our new LB07 light bar contains 12 high power Single intensity LEDs. There are three built in strobe patterns that will demand attention from anyone behind your vehicle. There is a constant strobe pattern, a double beat and a quad beat pattern, check out the video. When the brake is applied the LED will strobe based on what pattern you have selected. The unit comes pre-taped with 3M double sided tape for easy mounting to any flat surface. Works with any 12VDC system, no load equalizer or resistors required. Dimensions: 4.7" long x .7" wide x .7" high. Available in Red.
Knight Riderz Sequential LED Turn Signal Light Bars This light bar contains 12 high power sequential LEDs. When your turn signal is activated, the unit will initiate a sequence that corresponds to your turn signal flash. The unit will work with flashers that flash between 60-120 times per second, standard DOT rate. The unit comes pre-taped with 3M double sided tape for easy mounting to any flat surface. Simply connect the black wire to any ground wire, the Red wire to your a existing power source and the blue wire to your turn signal. Works with any 12VDC system. Dimensions: 4.7" long x .7" wide x .7" high. Available in Red and Amber. Works great for auxiliary turn signals, mounts to saddle bags, trike fenders, etc. A pair of Knight Riderz are required, one for a left turn signal and one for a right turn signal, please enter a quantity of 2 when ordering.
Knight Rider LED Motorcycle License Plate Frames
Choice of Brilliant Chrome or Black Power Coat License Plate Frame Choice of Sequential or Non Sequential Knight Rider LED Light Bars (LB01, LB02, LB03, LB07, LB01S, LB02S, LB03S) Mounting Hardware Included Optional White LED License Plate Illuminator Bolts Dimensions: - will fit most states license plates (7-3/16" x 4-1/4"), except Maryland Sequential Light Bar: This light bar contains 12 high power intensity LEDs. In running light mode the LEDs sequence from side to side in a "Knight Rider" sequence. When the brake is applied the LED will flash for approximately 5-6 seconds then go to a solid on state until the brake is released. Both modes, running and brake, have been designed to create the maximum visibility. Simply connect the black wire to any ground wire, the Red wire to your existing brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required. Non Sequential Light Bar: This light bar contains 12 high power dual intensity LEDs. In running light mode the LEDs are on in low intensity mode. When the brake is applied the LED will flash for approximately 5-6 seconds then go to a solid on state until the brake is released. Both modes, running and brake, have been designed to create the maximum
visibility
Knight Riderz LED Auto & Truck License Plate Frames
Choice of Brilliant Chrome or Black Power Coat License Plate Frame LB22 Light Bar Mounted; Choice or Red or Smoked (Red Shown) Fits all US states license plate frames Sequential Light Bar: This light bar contains 21 high power intensity LEDs. In running light mode the LEDs sequence from side to side in a "Knight Rider" sequence. When the brake is applied the LED will flash for approximately 5-6 seconds then go to a solid on state until the brake is released. Both modes, running and brake, have been designed to create the maximum visibility. Simply connect the black wire to any ground wire, the Red wire to your existing brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required.
|
|
