| ||||||||||||||||||||||||||||||||||||||||||||||
Flasher RelaysCustom Dynamics offers 3 Flasher Units: Note: These units are not self canceling. Your motorcycle MUST have a replaceable two wire flasher relay to use these products. A few motorcycles have flasher relays which can not be replaced due to the fact that they are integrated into other electronics. Most flasher relays are located under the seat or behind the headlights. Please review your repair manual, or consult an expert as to whether your motorcycles flasher relay is replaceable. If you find that your motorcycles flasher relay is not two-wire and/or replaceable, please use the universal load equalizer, if you have a H-D, please use our Smart Equalizer.
Our Electronic LED Flasher relay directly replaces the stock flasher relay on most metric bikes! This unit is replace all 2 or 3 pin 12 Volt flashers. This unit will work from 0.05A up to 10A loads. These Units are Plug and Play with the Following Bikes and hardwire with any other 2 or 3 pin flasher. Yamaha: YZF-R1, YZF-R6, YZF600, FZ-1, FJR1300 Honda: CBR1000RR, RC-51, CBR600F4i, CB919, ST1300, GL1500, CBR1100XX, CBR900RR, CBR929RR, CBR600F2, CBR600F3, CBR600F4, VTR1000R Super Hawk, VT600, 02-04 1800 C, 02-03 1800 R models, 02-03 1800 S models, 04-05 1300 C models, 03-05 1300 S models, 05 1300 R models, 06 1300 C models.
02-08 Honda Kawasaki: ZX-10R, ZX-12R, ZX-6R(R) up to 04, Z-1000, ZXR1200(1100), ZZR1200, ZX1200, ZR-7 Yamaha: Roadstar or V-Star - hard wire installation as follows when replacing OEM relay with our Electronic LED Flasher Relay:
Motorcycle Brown wire to ELFR Red wire
Motorcycle Brown/white stripe wire to ELFRX Black wire
view picture Yamaha Cruiser Instructions
These Units are Plug and Play with the Following Bikes: Yamaha: YZF-R1, YZF-R6, YZF600, FZ-1, FJR1300 Honda: CBR1000RR, RC-51, CBR600F4i, CB919, ST1300, GL1500, CBR1100XX, CBR900RR, CBR929RR, CBR600F2, CBR600F3, CBR600F4, VTR1000R Super Hawk, VT600, 02-04 1800 C, 02-03 1800 R models, 02-03 1800 S models, 04-05 1300 C models, 03-05 1300 S models, 05 1300 R models, 02-08 Honda VFR Kawasaki: ZX-10R, ZX-12R, ZX-6R(R) up to 04, Z-1000, ZXR1200(1100), ZZR1200, ZX1200, ZR-7 Suzuki: All late model GSXR's with two-wire replaceable flasher relays are also compatible, but require a hard-wire installation. Ducati: 996 - hard wire installation as follows when replacing OEM relay with our Electronic LED Flasher Relay:
Motorcycle Light Blue (LB) gets connected to the Adjustable Rate Flasher Red wire
Motorcycle Pink (P) gets connected to the Adjustable Rate Flasher White or Yellow wire
Motorcycle Black is connector to Adjustable Rate Flasher Black wire
Yamaha: Roadstar or V-Star - hard wire installation as follows when replacing OEM relay with our Electronic LED Flasher Relay:
Motorcycle Brown wire to Flasher Red wire
Motorcycle Brown/white stripe wire to Flasher White or Yellow wire
Motorcycle Black Wire to Flasher Black
view picture Yamaha Cruiser Instructions HARD WIRE INSTALLATION INSTRUCTIONS: if your existing flasher relay is a two wire flasher relay (or a three wire with a ground wire), and you have access to it, you can replace it with our flasher relay as follows: Adjustable Flasher HARD WIRE INSTRUCTIONS
Red wire on Flasher to power source (ignition switched +12v)
White or Yellow wire on Flasher to load (blinker lamps/ blinker switch)
Black wire on Flasher to ground
Installation Instructions for Bikes Requiring Splice in Method
Introducing the Custom LED ELFR-P Programmable Electronic Flasher Relay! This micro controller based, plug and play flasher relay has 10 preprogrammed user selectable flash patterns! The flash pattern is easily selected by a 10 position rotary switch conveniently located on the compact unit. This flasher relay system will operate properly and consistently for blinker loads ranging from 0.1A to 5A, which basically covers any combination of any blinker products on the market! The fuse protected 18" long harness allows for plug and play* operation for motorcycles listed in our computability list below. For motorcycles not on the list, the unit may be hard wired to any motorcycle with a two wire flasher relay, or three wire flasher relay system where the third wire is a ground. The extra long length allows for convenient mounting of the flasher relay, for easy access during flash pattern selection. Each flash pattern was optimized for effectiveness when used with ANY type of blinker indicators such as: LED blinkers, stock blinkers, incandescent blinkers or integrated LED tail lights! There are several different flash patterns ranging from DOT (stock) blink patterns to super intense strobing patterns to slow fading patterns. You can be sure to find a pattern that suits your taste! * in addition to the direct plug and play connector, a single ground wire with affixed loop connector must be connected to the negative battery terminal. These Units are Plug and Play with the Following Bikes: Yamaha: YZF-R1, YZF-R6, YZF600, FZ-1, FJR1300 Honda: CBR1000RR, RC-51, CBR600F4i, CB919, ST1300, GL1500, CBR1100XX, CBR900RR, CBR929RR, CBR600F2, CBR600F3, CBR600F4, VTR1000R Super Hawk, VT600, 02-04 1800 C, 02-03 1800 R models, 02-03 1800 S models, 04-05 1300 C models, 03-05 1300 S models, 05 1300 R models, 02-08 Honda VFR Kawasaki: ZX-10R, ZX-12R, ZX-6R(R) up to 04, Z-1000, ZXR1200(1100), ZZR1200, ZX1200, ZR-7 Suzuki: All late model GSXR's with two-wire replaceable flasher relays are also compatible, but require a hard-wire installation. Ducati: 996 - hard wire installation as follows when replacing OEM relay with our Electronic LED Flasher Relay:
Motorcycle Light Blue (LB) gets connected to the ELFR-P Red wire
Motorcycle Pink (P) gets connected to the ELFR-P Black wire
Motorcycle Black is not used.
Yamaha: Roadstar or V-Star - hard wire installation as follows when replacing OEM relay with our Electronic LED Flasher Relay:
Motorcycle Brown wire to ELFR-P Red wire
Motorcycle Brown/white stripe wire to ELFR-P Black wire
HARD WIRE INSTALLATION INSTRUCTIONS: if your existing flasher relay is a two wire flasher relay (or a three wire with a ground wire), and you have access to it, you can replace it with our flasher relay as follows: ELFR-P HARD WIRE INSTRUCTIONS
Red wire on ELFR-P to power source (ignition switched +12v)
White wire on ELFR-P to load (blinker lamps/ blinker switch)
Black wire on ELFR-P to negative terminal on battery
|
|
